omapl138Linux系统挂载ubifs经常报错

piliyouke

在使用TL138开发板，进行Linux程序测试时，经常会出现ubifs文件系统挂载失败：打印如下信息：这个时候板子再重启下有时候又好了。感觉文件系统不稳定。请问下是什么问题

[    2.578549] Freeing init memory: 176K
8 m$ ^$ ]( Z+ q$ j1 P[    3.495789] smsc911x smsc911x: eth0: SMSC911x/921x identified at 0xc882a000, IRQ: 116
[    4.520331] davinci_mdio davinci_mdio.0: resetting idled controller
6 z% d2 t: m, v; d1 O[    4.527646] net eth1: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=davinci_mdio-0:00, id=7c0f1)
[    5.822039] SysLink version : 2.21.01.05
[    5.822066] SysLink module created on Date:Sep  6 2016 Time:13:33:51
Attached to slave procId 0.
' p9 E$ y# I2 n, Q" ULoading procId 0.
Loaded file dspSyslink.out on slave procId 0.
Started slave procId 0.

$ H$ O5 W2 L/ O# u5 ?' B& r+ ?Please press Enter to activate this console. [    7.524222] PHY: davinci_mdio-0:00 - Link is Up - 100/Full
[   11.496328] UBI error: ubi_io_read: error -74 (ECC error) while reading 65 bytes from PEB 13:17872, read 65 bytes
[   11.506808] UBIFS error (pid 738): ubifs_read_node: bad node type (0 but expected 2)
[   11.514694] UBIFS error (pid 738): ubifs_read_node: bad node at LEB 11:13776, LEB mapping status 1
[   11.526210] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
[   11.537016] UBIFS error (pid 738): ubifs_leb_read: reading 2869 bytes from LEB 58:45824 failed, error -74
[   11.546730] UBIFS error (pid 738): try_read_node: cannot read node type 1 from LEB 58:45824, error -74
[   11.558028] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
[   11.568810] UBIFS error (pid 738): ubifs_read_node: bad node type (0 but expected 1)
[   11.576685] UBIFS error (pid 738): ubifs_read_node: bad node at LEB 58:45824, LEB mapping status 1
3 w5 T( `/ j% g" T[   11.585775] UBIFS error (pid 738): do_readpage: cannot read page 210 of inode 334, error -22
: s' j  o! G: p! _+ [+ S5 F[   11.596246] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
[   11.607050] UBIFS error (pid 738): ubifs_leb_read: reading 2869 bytes from LEB 58:45824 failed, error -74
[   11.616763] UBIFS error (pid 738): try_read_node: cannot read node type 1 from LEB 58:45824, error -74
: h" X" ?) o0 y* ~[   11.628059] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
[   11.638838] UBIFS error (pid 738): ubifs_read_node: bad node type (0 but expected 1)
[   11.646718] UBIFS error (pid 738): ubifs_read_node: bad node at LEB 58:45824, LEB mapping status 1
[   11.655806] UBIFS error (pid 738): do_readpage: cannot read page 210 of inode 334, error -22
[   11.666888] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
[   11.677809] UBIFS error (pid 730): ubifs_leb_read: reading 2869 bytes from LEB 58:45824 failed, error -74
/ C6 b  Y7 p6 f, z+ I. d' ~( B9 s[   11.687550] UBIFS error (pid 730): try_read_node: cannot read node type 1 from LEB 58:45824, error -74
[   11.698866] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
[   11.709651] UBIFS error (pid 730): ubifs_read_node: bad node type (0 but expected 1)
[   11.717524] UBIFS error (pid 730): ubifs_read_node: bad node at LEB 58:45824, LEB mapping status 1
' o- }7 ]9 `0 A# t5 R) \# u0 m2 i[   11.726616] UBIFS error (pid 730): do_readpage: cannot read page 210 of inode 334, error -22
  H1 F, \) c. @2 \  }
7 c" `) i3 C3 c& F: I
& I. p( D3 e2 {9 b- Y

human

是从nand启动还是SD卡启动的

piliyouke

human 发表于 2017-5-20 01:21
) u+ {" S# ~1 G/ ~是从nand启动还是SD卡启动的

" u# \2 V# E8 W0 l# ^5 o; j是从nand启动的。运行一段时间就会出现上述的现象。

human

你的程序是否用到EMIFA，跟nand可能会冲突的

piliyouke

human 发表于 2017-5-22 09:42
) C. m4 C; X3 b: m( i你的程序是否用到EMIFA，跟nand可能会冲突的

程序上是用到了EMIFA，上面挂载了外扩网口还有ADC呀。但是这个总线不可能不挂接外设呀。应该有方法去避免这种冲突吧

piliyouke

human 发表于 2017-5-22 09:42
2 s7 x. G& Z+ D  n你的程序是否用到EMIFA，跟nand可能会冲突的

EMIFA是硬件上的定性的东西，这个冲突我觉得CPU硬件应该会自己去解决处理。感觉不是这个冲突的问题