omapl138Linux系统挂载ubifs经常报错

piliyouke

在使用TL138开发板，进行Linux程序测试时，经常会出现ubifs文件系统挂载失败：打印如下信息：这个时候板子再重启下有时候又好了。感觉文件系统不稳定。请问下是什么问题

[    2.578549] Freeing init memory: 176K
% `; }' J0 z/ r9 P; k! M[    3.495789] smsc911x smsc911x: eth0: SMSC911x/921x identified at 0xc882a000, IRQ: 116
[    4.520331] davinci_mdio davinci_mdio.0: resetting idled controller
[    4.527646] net eth1: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=davinci_mdio-0:00, id=7c0f1)
[    5.822039] SysLink version : 2.21.01.05
[    5.822066] SysLink module created on Date:Sep  6 2016 Time:13:33:51
Attached to slave procId 0.
2 V7 @1 ]3 }2 Z, A$ M, b) uLoading procId 0.
Loaded file dspSyslink.out on slave procId 0.
/ b% W7 P% D+ VStarted slave procId 0.

  r% ~. H2 ]* U+ W$ m* |3 CPlease press Enter to activate this console. [    7.524222] PHY: davinci_mdio-0:00 - Link is Up - 100/Full
% R+ Q, V5 l6 x. {[   11.496328] UBI error: ubi_io_read: error -74 (ECC error) while reading 65 bytes from PEB 13:17872, read 65 bytes
7 M! o+ A' U8 J. A0 l" \  z[   11.506808] UBIFS error (pid 738): ubifs_read_node: bad node type (0 but expected 2)
[   11.514694] UBIFS error (pid 738): ubifs_read_node: bad node at LEB 11:13776, LEB mapping status 1
, C: ?$ S& b/ a+ R* B: A[   11.526210] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
$ `. E, P9 c6 t& d) T& V  v[   11.537016] UBIFS error (pid 738): ubifs_leb_read: reading 2869 bytes from LEB 58:45824 failed, error -74
[   11.546730] UBIFS error (pid 738): try_read_node: cannot read node type 1 from LEB 58:45824, error -74
8 _5 j$ ^8 ~% a5 B/ f/ e[   11.558028] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
2 o, O- n2 T1 G: q/ P[   11.568810] UBIFS error (pid 738): ubifs_read_node: bad node type (0 but expected 1)
[   11.576685] UBIFS error (pid 738): ubifs_read_node: bad node at LEB 58:45824, LEB mapping status 1
! T5 U' h0 e$ L. S: F, k[   11.585775] UBIFS error (pid 738): do_readpage: cannot read page 210 of inode 334, error -22
[   11.596246] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
[   11.607050] UBIFS error (pid 738): ubifs_leb_read: reading 2869 bytes from LEB 58:45824 failed, error -74
[   11.616763] UBIFS error (pid 738): try_read_node: cannot read node type 1 from LEB 58:45824, error -74
6 x6 f; F7 S4 {. J[   11.628059] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
[   11.638838] UBIFS error (pid 738): ubifs_read_node: bad node type (0 but expected 1)
+ o9 @( I9 N: R[   11.646718] UBIFS error (pid 738): ubifs_read_node: bad node at LEB 58:45824, LEB mapping status 1
  W5 K( C2 E- d$ {# k[   11.655806] UBIFS error (pid 738): do_readpage: cannot read page 210 of inode 334, error -22
7 F, i8 F9 ~# z/ e3 d[   11.666888] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
4 m7 n7 v6 n' k; R  ~1 w3 i[   11.677809] UBIFS error (pid 730): ubifs_leb_read: reading 2869 bytes from LEB 58:45824 failed, error -74
[   11.687550] UBIFS error (pid 730): try_read_node: cannot read node type 1 from LEB 58:45824, error -74
2 C- V6 C. \# [" b* h[   11.698866] UBI error: ubi_io_read: error -74 (ECC error) while reading 2869 bytes from PEB 60:49920, read 2869 bytes
: L4 F6 q2 H( ?  O" Q) c[   11.709651] UBIFS error (pid 730): ubifs_read_node: bad node type (0 but expected 1)
[   11.717524] UBIFS error (pid 730): ubifs_read_node: bad node at LEB 58:45824, LEB mapping status 1
' p; L/ _" \7 G5 r% U! `" j6 r[   11.726616] UBIFS error (pid 730): do_readpage: cannot read page 210 of inode 334, error -22
" B7 h  Q5 Y3 z" m  B
2 g7 G/ T1 p; c! b, C

human

是从nand启动还是SD卡启动的

piliyouke

human 发表于 2017-5-20 01:21
是从nand启动还是SD卡启动的

3 V' X) v0 r' K) U* F是从nand启动的。运行一段时间就会出现上述的现象。

human

你的程序是否用到EMIFA，跟nand可能会冲突的

piliyouke

human 发表于 2017-5-22 09:42
, }0 U1 [; R  n# ^$ ^! \你的程序是否用到EMIFA，跟nand可能会冲突的

程序上是用到了EMIFA，上面挂载了外扩网口还有ADC呀。但是这个总线不可能不挂接外设呀。应该有方法去避免这种冲突吧

piliyouke

human 发表于 2017-5-22 09:42
你的程序是否用到EMIFA，跟nand可能会冲突的

0 t8 ^) m2 ?* R5 c% G! Q: `: QEMIFA是硬件上的定性的东西，这个冲突我觉得CPU硬件应该会自己去解决处理。感觉不是这个冲突的问题